I have been doing some work on the Chieftain but its the dull stuff eg :like turning up brass end tubes for the front idlers & drive shafts for the sprockets. Its a collection of parts at the moment, but soon as I figure out how they go on to the tank I'll post some more photo's.
Hope to get some time to work on the tank tomorrow & Friday
The bit of the Chieftain I'm working on at the moment took a lot more time & work than I had imagined but I now have two rear drive axels. And they have been locked onto the rear sprockets, fitted through bearings on the outside & inside of the rear hull, & managed to fit a rear drive sprocket onto the shafts for drive chains from the motors.
Due to the layout of the chieftain I had very little room for a drive sprocket & chain to fit. Using the smallest drive sprocket I could find that would fit onto a 10mm drive shaft, I managed to get the chain to run round it without interfering with the rear hull by just 2-3mm. It was looking as if I would have to grind into the rear hull for clearance...but I just got away with it.
Anyway some more photos, doesn't look like I've done much... most of the time was on the lathe machining shafts or drilling & tapping holes for grub screws... fitting & re-fitting until they ran true.
https://lh3.googleusercontent.com/3KUUN ... 98-h673-no
https://lh3.googleusercontent.com/Glf4T ... 00-h673-no
https://lh3.googleusercontent.com/g53-u ... 98-h673-no
https://lh3.googleusercontent.com/2pwSG ... 05-h673-no
Saddle bearings bolted to rear hull for rigidity.
https://lh3.googleusercontent.com/5Whth ... 36-h673-no
Small sprocket fitted, tapped hole with threaded grub screw locking it into position.
https://lh3.googleusercontent.com/N-IPw ... 03-h673-no
I need slight alinement adjustment with the motor sprockets & I need to test the final speed. I have a smaller & larger sprockets for the motors to adjust drive speed.
https://lh3.googleusercontent.com/IL31G ... 05-h673-no
https://lh3.googleusercontent.com/PD1wf ... 98-h673-no
https://lh3.googleusercontent.com/A3Bmq ... 98-h673-no
Just showing how close the chain clearance.
https://lh3.googleusercontent.com/ABiYv ... 98-h673-no
That's it for now, a few more adjustments to the motor sprockets, cut & tighten chains, wire in speed controller & test sprocket speed. Then I start on the road wheels & tracks
Well done, looks quite a tight fitment, i guess that explains the design of the final drive casing on the chieftain, it not only reduced the gearing but also moved the output shaft axis outside the hull envelope - make sense when you think about it.
I have been at a wedding this weekend so have achieved nothing unfortunately, either on CRARRV or on Robs grills......
life & work seem to get in the way. This afternoon managed to drop into the man cave & work on the build, after a lot of measuring, measuring again I took the jump into cutting the drive chains. After some tweaking & motor alinements, gear greasing I wired up the motors for a test expecting some of major problem. "It worked " I'm not going to know if I have the gear speed right until l finish the rest of the suspension, tracks & it moves but it works & the chain final drive clears the inner rear hull by about 4mm without me having to do any clearance cutting
Here my poor quality video clip
1st Happy New Year, 2017...year 3 on the Chieftain MK11 build. Still a long way to go, but still aiming to get a rolling hull this year. I've been working on the alignment of the idlers & rear sprockets...L/H side was ok, but the R/H side was somehow out hitting the side of the outer track guard. After a whole day measuring again & re-fitting it was re-aligned correctly. One side of Chieftain track has been roughly put together to help with the correct alignment of my next hurdle... building, mounting, of the road wheel bogies & upper track idlers.
Anyway some photos of the track & some road wheels placed roughly in position. Having the tracks in place make the tank look much bigger
https://lh3.googleusercontent.com/kM15F ... 50-h622-no
https://lh3.googleusercontent.com/ia2E6 ... 06-h622-no
https://lh3.googleusercontent.com/gOP6e ... 50-h253-no
https://lh3.googleusercontent.com/po6o_ ... 30-h622-no
https://lh3.googleusercontent.com/bcHTn ... 30-h622-no
https://lh3.googleusercontent.com/FBBs3 ... 30-h622-no
https://lh3.googleusercontent.com/WbIPB ... 30-h622-no
That's it for now cheers Gary
Who is online
Users browsing this forum: No registered users and 2 guests